1801 Eagle - 1801 $10 NGC AU55. This Choice AU 1801 Capped Bust Eagle has significant mint luster remaining in protected areas of both sides. The strike of this 1801 Eagle is above average with full details on some of the stars, Libertys hair, the eagles neck, the wings, the stars above, and the clouds. The dentils on both sides are complete but stronger on the obverse. Just a slight bit of wear keeps this coin from a Mint State grade. The surfaces are original and clean with no notable abrasion marks worthy of mention.

The coin is identified as the BD-2 variety because Star 8 has two points towards the cap, and Star 13 almost touches the bust. On the reverse the eagles beak almost touches Star 12. Most of 1801 eagles are this variety. It is most likely that the BD-1 dies broke during production and were replaced with this second type. The reverse die was used again in 1803.

The obverse design shows a profile of Liberty facing right. Below her is the date which is off center to the left. Between the date and the word LIBERTY on the left side of the coin are 8 stars. Another 5 stars follow LIBERTY down to the bust. Liberty wears a large, soft cap. Her hair flows down and also shows on her forehead. The design was probably taken from a Roman engraving of a Greek goddess. Libertys cap was certainly not a Phrygian or liberty cap. The liberty cap, emblematic of freedom, was worn by freed slaves and freed gladiators in Roman times. It was a close fitting cap used to cover a shorn head, which was one of the ways slaves were identified. Because of the way Libertys hair strands wrap around it, the oversized cap has been called a turban, and the design has been called the Turban Head because of it.

The reverse, issued in 1797, shows a heraldic eagle. However, Scot mixed up the positions of the arrows and olive branch. The arrows held in the wrong claw signify defiant militarism. Either Scot made an error copying the image of the Great Seal, or he deliberately changed the symbolism in keeping with very warlike stance. Considering that the United States at this time was engaged in a naval war with France (the undeclared Franco-American War of 1798 to 1800, which took place on the East coast of North America and the Caribbean and resulted in the end of French privateer attacks on U.S. shipping), the latter is probably more likely. The French would be especially sensitive to a message within the heraldry, and the young United States was brash in that they had just defeated the super power, England in gaining independence. In the field above the eagle are thirteen stars and above them, an arc of clouds. A banner from wing to wing has the motto E PLURIBUS UNUM.

Scot was born in 1744 in Edinburgh, Scotland or England. (Documentary evidence is lacking as to where he was born.) He was trained as a watchmaker in England and learned engraving afterwards. He moved to the United States in 1777, where he worked as an engraver of plates, bills of exchange, and office scales. During the Revolution, he was an engraver of paper money. In 1780 he was made the State Engraver of Virginia. He moved to Philadelphia the next year. He was appointed Chief Engraver of the United States Mint on November 23, 1793 by David Rittenhouse, Mint Director. Scots ability to make dies was limited, and he was advanced in years with failing eyesight. His work was somewhat less than that done in Europe at the time, and Scot was criticized for its poor quality. He was responsible for designs of most of Americas first coins.

The early Mint in Philadelphia had many challenges. Each of the specialists, the designers, engravers, and press operators were men who had previously worked in other fields. Coin manufacturing was a new trade for them. Production was sporadic. For the new Mint to coin each of the mandated denominations, it took four years. This delay was partly because of inexperience and governmental obstacles. Bonds that were unrealistically high were impediments to engravers working with precious metals. Congress was not united on the need for a government mint since private and foreign coinage seemed to work. Because of the non-existent or low production numbers in the early years of the Mint, foreign copper, silver and gold circulated along with American made coins for many years until they were later demonetized.